(iPhone 7 No Touch Solution) |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{Repair Guide | {{Repair Guide | ||
|Device= | |Device=iPhone 7, IPhone 7 Plus | ||
|Affects parts= | |Affects parts=Main Logic Board | ||
|Needs equipment= | |Needs equipment=Soldering Iron, Hot Air Station, Microscope | ||
|Type= | |Type=BGA, Soldering | ||
|Difficulty= | |Difficulty=3. Hard | ||
}} | }} | ||
{{stub}} | |||
==Problem description== | ==Problem description== | ||
No Touch — Phone turns on but touch doesn't work | No Touch — Phone turns on but touch doesn't work | ||
==Symptoms== | ==Symptoms== | ||
| Line 15: | Line 15: | ||
==Solution== | ==Solution== | ||
*Diode mode the LCD connector (J4502) and check for any lines that are OL or 0. | *Diode mode the LCD connector (J4502) and check for any lines that are OL or 0.000V (shorted). | ||
*In most cases, you'll find pry damage near the connector, causing damage to a filter or resistor. Commonly damaged: | *In most cases, you'll find pry damage near the connector, causing damage to a filter or resistor. Commonly damaged: | ||
**FL3917 | **FL3917 | ||
| Line 28: | Line 28: | ||
*If you found the diode mode readings are all normal, then most likely it's a connector issue | *If you found the diode mode readings are all normal, then most likely it's a connector issue | ||
*Find the 4 ground pins on the LCD and Home Button connectors and use fine tip tweezers or an Xacto blade to bend them outwards. | *Find the 4 ground pins on the LCD and Home Button connectors and use fine tip tweezers or an Xacto blade to bend them outwards. | ||
*Refer to the example image | *Refer to the example image | ||
* | *[[File:IP7 No Touch Fix.jpg|alt=How To Fix No Touch on iPhone 7|none|thumb|How To Fix No Touch on iPhone 7]] | ||
*Usually this issue is caused from too many screens being unplugged and plugged in, causing those pins to be pushed outwards | *Usually this issue is caused from too many screens being unplugged and plugged in, causing those pins to be pushed outwards | ||
*Or from someone plugging in a 8/8P screen into a 7/7P board. | *Or from someone plugging in a 8/8P screen into a 7/7P board. | ||
*If still no touch, you can try replacing the LCD connector to see if that solves it. | *If still no touch, you can try replacing the LCD connector to see if that solves it. | ||
Latest revision as of 08:59, 22 January 2024
| How To Fix an iPhone 7 With No Touch | |
|---|---|
| Device | iPhone 7, IPhone 7 Plus |
| Affects part(s) | Main Logic Board |
| Needs equipment | Soldering Iron, Hot Air Station, Microscope |
| Difficulty | ◉◉◉◌ Hard |
| Type | BGA, Soldering |
This article is a stub. You can help Repair Wiki grow by expanding it
Problem description
No Touch — Phone turns on but touch doesn't work
Symptoms
- Turns on but no touch
Solution
- Diode mode the LCD connector (J4502) and check for any lines that are OL or 0.000V (shorted).
- In most cases, you'll find pry damage near the connector, causing damage to a filter or resistor. Commonly damaged:
- FL3917
- FL3910
- R3923
- If you find an abnormal diode mode value, see if the name of the line mentions the word "touch. This will help assure you that you're looking at the right spot
- Follow the path of the abnormal value by doing diode mode readings on every component in the path, to see where the correct diode mode reading is located. That will point you towards the failed component.
- For example, if the top side of FL3917 gives you OL, but the bottom side of it gives you 0.442, then you found your failed component.
Another solution:
- If you found the diode mode readings are all normal, then most likely it's a connector issue
- Find the 4 ground pins on the LCD and Home Button connectors and use fine tip tweezers or an Xacto blade to bend them outwards.
- Refer to the example image
- Usually this issue is caused from too many screens being unplugged and plugged in, causing those pins to be pushed outwards
- Or from someone plugging in a 8/8P screen into a 7/7P board.
- If still no touch, you can try replacing the LCD connector to see if that solves it.
