How To Fix an iPhone 7 That Does Not Turn On, urrent jumps back and forth from 0 A to 320 mA, then 0 A to 1.4 A, then 0 A to 500 mA, and so on: Difference between revisions

How To Fix an iPhone 7 That Does Not Turn On, urrent jumps back and forth from 0 A to 320 mA, then 0 A to 1.4 A, then 0 A to 500 mA, and so on
Device	IPhone 7, IPhone 7 Plus
Affects part(s)	Main Logic Board
Needs equipment	Soldering Iron, Hot Air Station, Microscope
Difficulty	◉◉◉◌ Hard
Type	BGA, Soldering

VisualWikitext

Revision as of 20:57, 20 January 2024

This article is a stub. You can help Repair Wiki grow by expanding it

Problem description

No Power — After prompt to boot on DC power supply, current jumps back and forth from 0 A to 320 mA, then 0 A to 1.4 A, then 0 A to 500 mA, and so on

Symptoms

No current draw before prompt to boot on DC power supply
After prompt to boot, you see the current jump quickly between 0 A and various values, like 0 A > 320 mA > 0 A > 1.4 A > 0 A > 500 mA

Solution

Diagnostic Steps

Check for shorts around NAND
Usually you'll find these lines with a shorted capacitor:
- PP3V0_NAND
- PP0V9_NAND
If so, find the shorted capacitor by injecting voltage

Please note: PMIC (U1801) will often show lots of heat if you're testing with the DCPS connected through the battery connector but it's not the cause of the short. The short is at the capacitor next to NAND, but since you're connected to the battery connector, the current has to flow through PMIC to get to the short cap, hence the PMIC heats up.

Another Possible Cause:

Sometimes, you'll see this same behavior when PP1V8_SDRAM or PP1V1_SDRAM is shorted. If this is the case, you'll need to check for heat above the CPU. If you find PP1V8_SDRAM or PP1V1_SDRAM is shorted and find heat above the CPU, then it's a RAM short.

You'll need to replace RAM to solve it. This a very advanced repair and should only be done by those who've mastered this repair. It's very easy for things to go wrong and damage the CPU.

Repair Steps

Once you find the shorted capacitor, you can remove it and confirm the short is cleared.

@@ Line 9: / Line 9: @@
 ==Problem description==
-Provide a concise description of the issue here. Be  as specific as possible to help readers quickly determine whether or not this is the exact problem they are facing.
+No Power — After prompt to boot on DC power supply, current jumps back and forth from 0 A to 320 mA, then 0 A to 1.4 A, then 0 A to 500 mA, and so on
 [[File:Placeholder image.jpg|thumb|Example image (Figure 1) -- No image yet. Help expand this page by uploading it!]]
 ==Symptoms==
-Detail all measurable or observable symptoms in this section.
+* No current draw before prompt to boot on DC power supply
+* After prompt to boot, you see the current jump quickly between 0 A and various values, like 0 A > 320 mA > 0 A > 1.4 A > 0 A > 500 mA
-*Symptom 1 (Figure 1)
+==Solution==
-*Symptom 2
+===Diagnostic Steps===
-==Solution==
+* Check for shorts around NAND
-If the issue has a single, specific solution, provide it in this section and delete the sub-headers below. Otherwise, if there are multiple potential causes for the problem, outline the process of identifying the root cause and offer corresponding solutions below.
+* Usually you'll find these lines with a shorted capacitor:
+** PP3V0_NAND
+** PP0V9_NAND
+* If so, find the shorted capacitor by injecting voltage
+'''Please note:''' PMIC (U1801) will often show lots of heat if you're testing with the DCPS connected through the battery connector but it's not the cause of the short. The short is at the capacitor next to NAND, but since you're connected to the battery connector, the current has to flow through PMIC to get to the short cap, hence the PMIC heats up.
-===Diagnostic Steps===
+=== Another Possible Cause: ===
+[[File:IPhone 7 Plus RAM Short.jpg|alt=iPhone 7 Plus with SDRAM short|none|thumb|iPhone 7 Plus with SDRAM short]]
+Sometimes, you'll see this same behavior when PP1V8_SDRAM or PP1V1_SDRAM is shorted. If this is the case, you'll need to check for heat above the CPU. If you find PP1V8_SDRAM or PP1V1_SDRAM is shorted and find heat above the CPU, then it's a RAM short.
+You'll need to replace RAM to solve it. This a very advanced repair and should only be done by those who've mastered this repair. It's very easy for things to go wrong and damage the CPU.
 ===Repair Steps===
+Once you find the shorted capacitor, you can remove it and confirm the short is cleared.