(Created page with "{{stub}} {{Repair Guide |Device= |Affects parts= |Needs equipment= |Type= |Difficulty= }} ==Problem description== Addressing issues with MacBook Pro ''820-01598'' not detecting the camera. thumb|Example image (Figure 1) -- No image yet. Help expand this page by uploading it! ==Symptoms== *Camera not detected *Possible burned or exploded L8504 filter on TCON board ==Solution== ===Diagnostic Steps=== ====Check L8504 Continuity==== *Use a...") |
No edit summary |
||
| Line 1: | Line 1: | ||
{{Repair Guide | {{Repair Guide | ||
|Device= | |Device=MacBook Pro A2159 | ||
|Affects parts= | |Affects parts=Motherboard | ||
|Needs equipment= | |Needs equipment=multimeter, soldering iron, soldering station | ||
|Type= | |Type=Soldering, Micro-Soldering | ||
|Difficulty= | |Difficulty=3. Hard | ||
}} | }} | ||
{{stub}} | |||
==Problem description== | ==Problem description== | ||
Addressing issues with MacBook Pro ''820-01598'' not detecting the camera. | Addressing issues with MacBook Pro ''820-01598'' not detecting the camera. | ||
Revision as of 19:07, 28 September 2023
| MacBook Pro A2159 No camera detected repair | |
|---|---|
| Device | MacBook Pro A2159 |
| Affects part(s) | Motherboard |
| Needs equipment | multimeter, soldering iron, soldering station |
| Difficulty | ◉◉◉◌ Hard |
| Type | Soldering, Micro-Soldering"Micro-Soldering" is not in the list (Soldering, Teardown, Part replacement, Cleaning, Software, BGA, General) of allowed values for the "Repair Guide type" property. |
This article is a stub. You can help Repair Wiki grow by expanding it
Problem description
Addressing issues with MacBook Pro 820-01598 not detecting the camera.
Symptoms
- Camera not detected
- Possible burned or exploded L8504 filter on TCON board
Solution
Diagnostic Steps
Check L8504 Continuity
- Use a multimeter in continuity mode to check L8504 (Figure 1).
- Normal reading should be close to 0.01.
- If L8504 is blown or burned, proceed to the "L8504 blown or visibly burned repair steps" below.
Test with Known Good Display
- Verify camera function using a KNOWN GOOD display assembly.
- If the camera works with a different display, the original display might be faulty.
- Make sure to check L8504 before diagnosing the display issue.
Repair Steps
Camera Works with Known Good Display
If camera works with a known good test display, replace the display assembly.
L8504 Blown or Visibly Burned
- Understand that L8504 failure indicates a catastrophic short within the TCON board of the display or a melted/corroded display cable/connector.
- Repair L8504 only after addressing the display issue, as L8504 might fail again if the display issue persists.
- When replacing L8504, address corresponding pad and trace damage.
- Use 36 or 37 AWG enamel coated copper wire for jumper wires due to webcam and ambient light sensor power requirements.
- Connect jumper wire from the input side of the filter (PP5v_G3S) C5250.
- Apply conformal coating to jumper wire.
- Use a 120 Ohm ferrite filter rated for 1.5 amps (402 package size).
- After replacing L8504 and addressing trace issues, replace the display assembly or repair it by replacing damaged cables/connectors.
No Camera Function, L8504 Normal
- Attempt to restore T2/BridgeOs firmware via Apple Configurator 2 by entering DFU mode.
- Ensure your Mac is on the latest macOS version.
- Follow Apple's support article on reviving or restoring T2/BridgeOs firmware.
- If no camera function after firmware revive, and other causes are ruled out, U8504 might be faulty, or there could be trace/resistor issues between the camera connector/U8504 or between U8504 and the T2 chip.
- A hardware issue with the T2 chip might also cause camera detection problems.
If it is not any of the above, then it might be a failed camera secure disable chip (U8502). This is very rare.