How To Fix an iPhone 15 That Randomly Restarts: Difference between revisions

How To Fix an iPhone 15 That Randomly Restarts
Device	iPhone 15, iPhone 15 Plus
Affects part(s)	Main Logic Board
Needs equipment	Screwdrivers, known good parts, spudger
Difficulty	◉◌◌◌ Easy
Type	Part replacement

Latest revision as of 08:18, 8 January 2024

Problem description

There are many reasons that could cause an iPhone 15 and iPhone 15 Plus to randomly restart every few minutes. For the iPhone 15 series, there are some sensors within the parts of the phone that are required to be plugged in & detected. Otherwise, the phone restarts on its own.

The most common for iPhone 15 series are:

Back Glass/Wireless Charging Flex- This is the flex that is attached to the Back Glass. It can damaged during a drop or screen replacement
Proximity Flex -This is the flex that is attached to the screen. It can easily be liquid damaged or torn during a screen replacement.
Charging Port Flex - This is the flex towards the bottom of the phone. It is easily damaged with a drop & the back glass is breaks. Or when someone has repaired the back glass.

Symptoms

After a back glass repair, the iPhone will restart on its own every few minutes
After a hard drop, the iPhone will restart every 3 minutes.
After a screen repair, the iPhone will bootloop every 3 minutes
The iPhone will reboot randomly when using it.
The iPhone will seem to freeze and restart every 2-5 minutes.

Solution

Diagnostic Steps

Before you start blindly replacing parts, it's important to try to confirm what is causing the restarting issue by reviewing the Panic Log file. This is a file that is generated by the Operating System, to document the fault causing the restart.

An example of panic log files you'll find in the iPhone when it has been randomly restarting.

To find the panic log on the device, go to Settings-> Privacy-> Analytics & Improvements-> Analytics Data-> Scroll down to the files starting with "panic-full..." & click on the most recent dated file.

Then you'll want to scan through the text for keywords that may point you to the cause.

For this model, look for where it says "SMC PANIC - ASSERTION FAILED" ... "Sensor Array" .. "0x...."

If you see:

0x200000 - it's the Wireless Charging Flex (Back Glass)
- Make sure it's plugged in & the flex is not torn
- Check that there's no liquid damaged, or that it's defective
- Test with OEM or Premium. Aftermarket Flexes have a high defect rate
- Diode mode the FPC connectors for any faults
- Could be a sandwich issue

0x80000 - it's the Charging Port Flex
- Make sure this flex is plugged in
- Check that no flex is torn, liquid damaged, defective
- Test with OEM or Premium. Aftermarket Flexes have a high defect rate
- Diode mode the FPC connectors for any faults
- Could be a sandwich issue

0x100000 - it's the Proximity Flex Cable
- Make sure this flex is plugged in
- Check that no flex is torn, liquid damaged, defective
- Test with OEM or Premium. Aftermarket Flexes have a high defect rate
- Diode mode the FPC connectors for any faults

Alternatively, you can use a tool like the iDevice Panic Log Analyzer, which will download the panic logs from the device & display them on the PC & give you suggestions to possible solutions. It makes it easier to browse the panic log file.

Also check out www.PanicFull.com which allows you to upload the panic log file & have it analyzed for free.

Both of these tools just give suggestions, which aren't always correct, as there is no official solution list from Apple. So many solutions are just suggestions based on hearsay, rumors or just guesses.

For situations where you don't see the above examples, you'll have to read through the top portion of the panic log & try to decipher what could be the root cause. Look for keywords you may recognize.

Repair Steps

When trying to solve for these issues, make sure to replace the appropriate flex with an OEM or Premium flex.

It is also a good idea to keep a known good power button flex & charging port flex in your bench, for testing only. There are reports of even NEW flexes being bad. So you have to keep known good flexes on hand at all times, so you don't waste your time troubleshooting with possibly bad flexes.

In scenarios where you have the appropriate flexes plugged in, but it still restarts, then you either have:

Bad or damaged flex
Low quality aftermarket flex
Other flex cables that are Liquid Damaged

Please note: You MUST have the required flex cables plugged in. Otherwise, it WILL restart. You cannot troubleshoot this step by unplugging the bad flex.

@@ Line 1: / Line 1: @@
-{{stub}}
 {{Repair Guide
-|Device=
+|Device=iPhone 15, iPhone 15 Plus
-|Affects parts=
+|Affects parts=Main Logic Board
-|Needs equipment=
+|Needs equipment=Screwdrivers, known good parts, spudger
-|Type=
+|Type=Part replacement
-|Difficulty=
+|Difficulty=1. Easy
 }}
 ==Problem description==
-Provide a concise description of the issue here. Be  as specific as possible to help readers quickly determine whether or not this is the exact problem they are facing.
+There are many reasons that could cause an iPhone 15 and iPhone 15 Plus to randomly restart every few minutes.
-[[File:Placeholder image.jpg|thumb|Example image (Figure 1) -- No image yet. Help expand this page by uploading it!]]
+For the iPhone 15 series, there are some sensors within the parts of the phone that are required to be plugged in & detected. Otherwise, the phone restarts on its own.
+The most common for iPhone 15 series are:
+* '''Back Glass/Wireless Charging Flex'''- This is the flex that is attached to the Back Glass. It can damaged during a drop or screen replacement
+*'''Proximity Flex''' -This is the flex that is attached to the screen. It can easily be liquid damaged or torn during a screen replacement.
+*'''Charging Port Flex''' - This is the flex towards the bottom of the phone. It is easily damaged with a drop & the back glass is breaks. Or when someone has repaired the back glass.
 ==Symptoms==
-Detail all measurable or observable symptoms in this section.
+*After a back glass repair, the iPhone will restart on its own every few minutes
+*After a hard drop, the iPhone will restart every 3 minutes.
-*Symptom 1 (Figure 1)
+*After a screen repair, the iPhone will bootloop every 3 minutes
-*Symptom 2
+*The iPhone will reboot randomly when using it.
+*The iPhone will seem to freeze and restart every 2-5 minutes.
 ==Solution==
-If the issue has a single, specific solution, provide it in this section and delete the sub-headers below. Otherwise, if there are multiple potential causes for the problem, outline the process of identifying the root cause and offer corresponding solutions below.
 ===Diagnostic Steps===
+Before you start blindly replacing parts, it's important to try to confirm what is causing the restarting issue by reviewing the Panic Log file. This is a file that is generated by the Operating System, to document the fault causing the restart.[[File:Panic Log List.png|thumb|An example of panic log files you'll find in the iPhone when it has been randomly restarting.]]To find the panic log on the device, go to Settings-> Privacy-> Analytics & Improvements-> Analytics Data-> Scroll down to the files starting with "panic-full..." & click on the most recent dated file.
+Then you'll want to scan through the text for keywords that may point you to the cause.
+For this model, look for where it says "SMC PANIC - ASSERTION FAILED" ... "Sensor Array" .. "0x...."
+If you see:
+*'''0x200000''' - it's the Wireless Charging Flex (Back Glass)
+**Make sure it's plugged in & the flex is not torn
+**Check that there's no liquid damaged, or that it's defective
+**Test with OEM or Premium. Aftermarket Flexes have a high defect rate
+**Diode mode the FPC connectors for any faults
+**Could be a sandwich issue
+*0x80000 - it's the Charging Port Flex
+**Make sure this flex is plugged in
+**Check that no flex is torn, liquid damaged, defective
+**Test with OEM or Premium. Aftermarket Flexes have a high defect rate
+**Diode mode the FPC connectors for any faults
+**Could be a sandwich issue
+*0x100000 - it's the Proximity Flex Cable
+**Make sure this flex is plugged in
+**Check that no flex is torn, liquid damaged, defective
+**Test with OEM or Premium. Aftermarket Flexes have a high defect rate
+**Diode mode the FPC connectors for any faults
+Alternatively, you can use a tool like the [https://github.com/waynebonc/iDeviceLogAnalyzer-public iDevice Panic Log Analyzer], which will download the panic logs from the device & display them on the PC & give you suggestions to possible solutions. It makes it easier to browse the panic log file.
+Also check out [https://Www.PanicFull.com www.PanicFull.com] which allows you to upload the panic log file & have it analyzed for free.
+Both of these tools just give suggestions, which aren't always correct, as there is no official solution list from Apple. So many solutions are just suggestions based on hearsay, rumors or just guesses.
+For situations where you don't see the above examples, you'll have to read through the top portion of the panic log & try to decipher what could be the root cause. Look for keywords you may recognize.
 ===Repair Steps===
+When trying to solve for these issues, make sure to replace the appropriate flex with an OEM or Premium flex.
+It is also a good idea to keep a known good power button flex & charging port flex in your bench, for testing only. There are reports of even NEW flexes being bad. So you have to keep known good flexes on hand at all times, so you don't waste your time troubleshooting with possibly bad flexes.
+In scenarios where you have the appropriate flexes plugged in, but it still restarts, then you either have:
+*Bad or damaged flex
+*Low quality aftermarket flex
+*Other flex cables that are Liquid Damaged
+Please note: You MUST have the required flex cables plugged in. Otherwise, it WILL restart. You cannot troubleshoot this step by unplugging the bad flex.